Use a stud finder to locate each stud. Sonance includes a cut-out template with each speaker. Tape the entire template to the wall with masking tape. Use a tape measure and a level to check the alignments.
Mark the inner dimensions of the template as well, just in case your template magically flies off the wall yes that did happen to me. Set up all the templates before making a single cut. I found out the hard way that readjusting a paper template is much easier than patching holes--I corrected three out of five holes because of a missed crossbeam and a doubled-up stud.
With all the templates fastened to the walls, recheck your measurements and play it safe--hit them with the level one more time. Start cautiously by drilling a pilot hole in the center of the first template. Push a piece of wire through the hole, spinning it around and feeling for obstacles. Increase the diameter of the hole gradually by 2 or 3 inches and recheck the cavity.
Eventually make the opening wide enough so you can carefully fit your hand inside. The wider opening makes it easier to inspect the wall cavity for obstructions like wires or something as small as a protruding screw or nail.
If something is blocking the installation, a hand-size hole is small enough that your template should have some wiggle room to move in one direction or another away from an obstruction. Don't forget that if you move one template, you have to move the others. It never hurts to measure again.
This time, measure inside the wall cavity in four directions up, down, left and right , making sure that the tape measure doesn't touch anything like extra beams. I told you I ran into problems. Once you've checked everything, the rest is easy. Use either a hand drywall saw or a reciprocating saw to cut the hole.
Start in the center, working your way down and across, then cutting upward in sections. The first one is the hardest; the rest go much faster. Route the speaker wires by inspecting your house for pre-made entryways into the cavity of the walls before drilling any holes. If you need to make an opening, drill a small hole and use a snake, drop chain and a coat hanger saved me a few times to pull the wire through the hole.
Going across the walls gets a bit more complicated, but a quick solution is to pull the baseboards off the wall and cut about a O inch of the drywall off using a utility knife. Now carefully staple wires to the exposed studs, then reattach the baseboards. Fastening the speakers to the wall is straightforward. Sonance Cinema Series speakers feature the RotoLock mounting system to secure the speakers tightly in place.
Hi, I am finishing my basement into a home theater and installing Paradigm AMS series inwall speakers.
NEC much? Submitted by TheJoBoo on December 9, - am. Thanks, JoBoo -- this last point very well taken. These were old photos picked up from an article published a long time ago in home theater, and I didn't notice that the cable shown in the open wall cavity is absolutely NOT code. In-wall speaker cable has the conductors in their own insulation as you see here and then contained within a protective sheath.
In-wall cable glides better through studs and walls, has better tensile strength to avoid breakage from pulls, and offers more protection from sharp protrusions. It's designed to work better and be safer when run in wall cavities shared with electrical lines. Related Latest Reviews News. Building a Home Theater?
Avoid these Pitfalls. Acoustics Review: Sonos S5 ZonePlayer and 3. Digital Media Receiver Roundup. Review: Pro-Ject RM New Gear for the New Year. Discovering YouTube. Beethoven, Regolith, and You. LG Reaches for the Stars with 9. Free Guy. Sonos Beam Gen 2 Soundbar Review. The Green Knight.
If you want the in-wall speakers to match the color of your walls, you will need to paint them before installation. Now, it is time to connect the speakers to the wires. After the connection, you need to insert the speakers into the wall and then screw them tightly into its place. Related: How to Install Outdoor Speakers. The last step on how to install in-wall speakers is to switch on the system and test how well the sound is working.
You need to perform the testing using a lower volume and then progress steadily until you are sure that the sound quality is right. So far, this article has provided you with all the instructions you need to learn on how to install in-wall speakers.
The facts presented in this guide will benefit you if you follow and implement them as they are. By so doing, you will be adding another golden feather on the cap of your home entertainment atmosphere. You can be assured of enriching the esthetic and entertainment ambiance of your home and turn it into a refreshing hub of quality music.
You must be logged in to post a comment. This site uses Akismet to reduce spam.
0コメント